Go Back   Maxum Boat Owners Club - Forum > Search Forums
Reload this Page Search Results
Click Here to Login
Register FAQ Community Calendar Today's Posts Log in

Showing results 1 to 11 of 11
Search took 0.01 seconds. Search: Posts Made By: mmwjr
Forum: Engines 09-24-2019, 09:16 PM
Replies: 28
Views: 3,422
Posted By mmwjr
You need to break out a volt meter and take...

You need to break out a volt meter and take readings when its not working.
Forum: Engines 09-24-2019, 09:13 PM
Replies: 28
Views: 3,422
Posted By mmwjr
Who said anything about the starter showing...

Who said anything about the starter showing amperage?

I said verify he has 12Vs on the yellow/red wire when cranking (not clear he was measuring when cranking). This is the wire from the slave...
Forum: Engines 09-18-2019, 11:29 AM
Replies: 28
Views: 3,422
Posted By mmwjr
If you have 12.6 volts on the starter solenoids...

If you have 12.6 volts on the starter solenoids coil wire (yellow/Red) when cranking then the neutral safety switch is not the issue. This would leave the start or its solenoid as the issue.
Forum: Engines 09-12-2019, 04:09 PM
Replies: 28
Views: 3,422
Posted By mmwjr
Even without visible signs of corrosion on the 10...

Even without visible signs of corrosion on the 10 pin connector some have trouble with poor continuity through it. If voltage at the engine breaker stay at 12V when you are trying to start you should...
Forum: Engines 09-12-2019, 11:27 AM
Replies: 28
Views: 3,422
Posted By mmwjr
I would try the next either measure the ignition...

I would try the next either measure the ignition switch I terminal which you have 12V with the key in the run position to see if it drops voltage when the key is turned to the start position or use a...
Forum: Engines 09-11-2019, 03:51 PM
Replies: 28
Views: 3,422
Posted By mmwjr
When trying to start check for voltage on the...

When trying to start check for voltage on the slave solenoid (number 1 in the pic) at its Red/Purple wire.

5976
Forum: Engines 09-11-2019, 11:34 AM
Replies: 28
Views: 3,422
Posted By mmwjr
You can call me Mike Since the alarm is...

You can call me Mike

Since the alarm is sounding that mean there is 12V on the ignition switch I terminal. as you said the alarm sounds in test mode due to no oil pressure. Did the engine crank...
Forum: Engines 09-05-2019, 12:12 AM
Replies: 28
Views: 3,422
Posted By mmwjr
Does the engine start now? What do you mean...

Does the engine start now?

What do you mean the alarm is on, buzzes with key on but engine not started and stops once engine is running?
Forum: Engines 08-28-2019, 11:47 AM
Replies: 28
Views: 3,422
Posted By mmwjr
Disconnect the connector and inspect the large...

Disconnect the connector and inspect the large pin for corrosion.
Forum: Engines 08-28-2019, 02:09 AM
Replies: 28
Views: 3,422
Posted By mmwjr
The alarm gets power from the I (ignition)...

The alarm gets power from the I (ignition) terminal of the ignition switch it then goes to the kill switch and finally the engine ignition coil and Thunderbolt ignition module. The S terminal on the...
Forum: Engines 08-27-2019, 11:37 PM
Replies: 28
Views: 3,422
Posted By mmwjr
Welcome aboard Can you rig up a voltmeter...

Welcome aboard

Can you rig up a voltmeter to the B terminal of the ignition switch to see if power here goes away when the issue occurs. This way you can isolate as either power not getting to...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT. The time now is 06:47 AM.

Contact Us - Maxum Owners Club - Archive - Community Rules - Terms of Service - Privacy - Accessibility - Top

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.