Forum: Engines
12-14-2014, 10:52 PM
|
Replies: 10
Views: 24,936
Hours are unknown. No hour meter if you can...
Hours are unknown. No hour meter if you can believe that. I thought all boats had em. The leakdown test indicated any leakage was at the rings. She doesn't smoke. Runs very good actually. Just not as...
|
Forum: Maxum Owners General Discussions
12-14-2014, 10:42 PM
|
Replies: 26
Views: 32,831
|
Forum: Maxum Owners General Discussions
12-14-2014, 10:35 PM
|
Replies: 20
Views: 17,213
|
Forum: Maxum Owners General Discussions
12-14-2014, 10:23 PM
|
Replies: 20
Views: 17,213
|
Forum: Engines
12-13-2014, 04:16 AM
|
Replies: 10
Views: 24,936
I wish I had 150 psi. My 1995 7.4 L has around...
I wish I had 150 psi. My 1995 7.4 L has around 105 psi each. I then did a leak down test and they came in at around 8 % . I was ready to pull it out and rebuild it. Then I found a Mercruiser Service...
|
Forum: Maxum Owners General Discussions
12-13-2014, 03:33 AM
|
Replies: 26
Views: 32,831
|
Forum: Maxum Owners General Discussions
12-13-2014, 03:02 AM
|
Replies: 20
Views: 17,213
|
Forum: Maxum Owners General Discussions
06-30-2010, 05:43 AM
|
Replies: 69
Views: 65,458
I wanted twin 7.4L around 35 feet and 12 foot...
I wanted twin 7.4L around 35 feet and 12 foot beam aprox. But thats just a little too big to trailer. Which i may have to do from time to time. Settled on single 7.4L Bravo2 1995 2700 SCR. 30x10...
|
Forum: Sport Cruisers
06-30-2010, 03:20 AM
|
Replies: 8
Views: 11,217
That is a bummer. Doesn't sound right to me....
That is a bummer. Doesn't sound right to me. Sorry to hear dude.
What's 5200 ? How do they check moisture content ? Don't mean to hi-jack thread but i've seen 2-3 inch stress crack in gel coat...
|
Forum: Sport Cruisers
06-30-2010, 02:35 AM
|
Replies: 19
Views: 5,275
Leak down test showed 8 % loss or less on all...
Leak down test showed 8 % loss or less on all except #6 cyl. Which was 20%. Appears exhaust valve. Not sealing proper and possibly sticking. I may (should) pull that head off when i do intake...
|
Forum: Maxum Maintenance
06-30-2010, 02:20 AM
|
Replies: 9
Views: 2,923
|
Forum: Sport Cruisers
06-25-2010, 02:18 AM
|
Replies: 19
Views: 5,275
I'm going to have to run engine to warm up at...
I'm going to have to run engine to warm up at shop. I have muffs i used on the alpha. Will they work on the bravo 2 . Or is the raw water intake somewhere else? Thanks
Randal
added;
Should...
|
Forum: Sport Cruisers
06-24-2010, 05:22 PM
|
Replies: 19
Views: 5,275
|
Forum: Sport Cruisers
06-24-2010, 05:10 AM
|
Replies: 19
Views: 5,275
|
Forum: Maxum Maintenance
06-24-2010, 04:22 AM
|
Replies: 9
Views: 2,923
Checked website. Cool. Says the won't send...
Checked website. Cool. Says the won't send outside of US. I'm from Canada. To bad. There is a service just over border that will receive and hold for a fee. I would just have to drive accross and...
|
Forum: Sport Cruisers
06-24-2010, 02:49 AM
|
Replies: 19
Views: 5,275
|
Forum: Forum Support | Suggestion Box | News
06-24-2010, 01:58 AM
|
Replies: 4
Views: 3,462
|
Forum: Maxum Maintenance
06-24-2010, 01:39 AM
|
Replies: 9
Views: 2,923
Thanks . I left a big list at my local marine...
Thanks . I left a big list at my local marine store (found small shop in town with very reasonable prices). They're getting parts prices for me. Then figure my labor and negotiate purchase of boat....
|
Forum: Sport Cruisers
06-24-2010, 01:02 AM
|
Replies: 19
Views: 5,275
I tried with paper, then paper towel. Didn't...
I tried with paper, then paper towel. Didn't suck.Had to hold over opening. Slight pressure pushing out. Almost neutral. Used soap on intake.Bubbles both sides of intake R&L at gasket at exhaust...
|
Forum: Maxum Maintenance
06-23-2010, 10:45 PM
|
Replies: 9
Views: 2,923
If i interpret SP correct. Grease nipple on...
If i interpret SP correct. Grease nipple on u-joint accessed through transom from engine bay(so no drive removal required). Nipple on transon mounting ring for gimble bearing accessed from engine...
|
Forum: Maxum Maintenance
06-23-2010, 12:22 PM
|
Replies: 9
Views: 2,923
Do i have to pull the drive off ? (I'd do...
Do i have to pull the drive off ? (I'd do impeller later ,is ok now) Saw 2 grease nipples on what i believe is coupler on back of engine bolted to engine. I'll look for rest. Thanks
Randal
|
Forum: Maxum Maintenance
06-23-2010, 04:10 AM
|
Replies: 9
Views: 2,923
1995 Bravo 2 454
Is there a gimble bearing grease nipple behind drive or in engine compartment? Does u-joint have grease nipple? Thanks 2700scr
Randal
|
Forum: Maxum Maintenance
06-23-2010, 03:52 AM
|
Replies: 10
Views: 3,781
I checked local marine parts store. Said he can...
I checked local marine parts store. Said he can get me Seloc for $40 canadian. Said there was another manual maker but couldn't think of who. I'll go to mercruiser dealer to see about factory manual....
|
Forum: Sport Cruisers
06-23-2010, 03:37 AM
|
Replies: 19
Views: 5,275
Its center manifold right side by carb , maybe...
Its center manifold right side by carb , maybe inch back. If i pull boat out is there grease nipple on u-joint or gimble bearing behind 1995 Bravo 2 drive (should i pull off drive)?. A saw grease...
|
Forum: Sport Cruisers
06-22-2010, 06:52 PM
|
Replies: 19
Views: 5,275
|