Go Back   Maxum Boat Owners Club - Forum > Search Forums
Reload this Page Search Results
Click Here to Login
Register FAQ Community Calendar Today's Posts Log in

Showing results 1 to 12 of 12
Search took 0.00 seconds. Search: Posts Made By: mmwjr
Forum: Engines 09-24-2017, 11:37 AM
Replies: 35
Views: 4,298
Posted By mmwjr
That will definitely block flow. Hopefully the...

That will definitely block flow. Hopefully the issue is now resolved.
Forum: Engines 09-11-2017, 10:01 PM
Replies: 35
Views: 4,298
Posted By mmwjr
Can't say I'm surprised. Well at least you know...

Can't say I'm surprised. Well at least you know the issue.
Forum: Engines 09-05-2017, 09:00 PM
Replies: 35
Views: 4,298
Posted By mmwjr
Yes, I had a car with a warped head that ran hot...

Yes, I had a car with a warped head that ran hot but no coolant in the oil.
Forum: Engines 08-23-2017, 09:43 PM
Replies: 35
Views: 4,298
Posted By mmwjr
Any progress with the hot engine?

Any progress with the hot engine?
Forum: Engines 08-21-2017, 03:49 PM
Replies: 35
Views: 4,298
Posted By mmwjr
In post #6 the OP said he verified good raw water...

In post #6 the OP said he verified good raw water flow to the HE therefore the transom assembly should not have blockage in the hose.
Forum: Engines 08-21-2017, 01:44 AM
Replies: 35
Views: 4,298
Posted By mmwjr
Well much easier and cheaper than the engine...

Well much easier and cheaper than the engine coupler.
Forum: Engines 08-21-2017, 01:40 AM
Replies: 35
Views: 4,298
Posted By mmwjr
I spun my BII prop many years ago. It would hold...

I spun my BII prop many years ago. It would hold as long as I did not exceed 1800 rpm, above that it would slip. Cost about $175 to replace hub and recondition the prop back then. BII aluminum props...
Forum: Engines 08-20-2017, 11:29 AM
Replies: 35
Views: 4,298
Posted By mmwjr
Good luck and keep us posted on the findings.

Good luck and keep us posted on the findings.
Forum: Engines 08-20-2017, 11:16 AM
Replies: 35
Views: 4,298
Posted By mmwjr
I think the overreving engine is a bad prop,...

I think the overreving engine is a bad prop, onyou have a spare to try?

So you plan to run barnacle buster in the closed cooling? Not sure why.
Forum: Engines 08-20-2017, 04:06 AM
Replies: 35
Views: 4,298
Posted By mmwjr
Yes a bad engine coupler will smell, you also...

Yes a bad engine coupler will smell, you also said you could hear the clutch shift but no motion do the prop would be my first place to look.

Have you used an IR sensor to verify engine temps?
Forum: Engines 08-20-2017, 03:25 AM
Replies: 35
Views: 4,298
Posted By mmwjr
The flywheel cover has the rear engine mounts...

The flywheel cover has the rear engine mounts built into it and it must be removed the replace the engine coupler which is bolted to the flywheel. I do not know of a coupler in the drive it's a...
Forum: Engines 08-19-2017, 09:43 PM
Replies: 35
Views: 4,298
Posted By mmwjr
Ok you ran the one good engine to hard with an...

Ok you ran the one good engine to hard with an off balanced load, assuming BII you either spun the prop hub or engine coupler. Another possibility is broken shift cable or drive it self.

On the...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT. The time now is 10:36 AM.

Contact Us - Maxum Owners Club - Archive - Community Rules - Terms of Service - Privacy - Accessibility - Top

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.