Go Back   Maxum Boat Owners Club - Forum > Search Forums
Reload this Page Search Results
Click Here to Login
Register FAQ Community Calendar Today's Posts Log in

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: mmwjr
Forum: Welcome Mat | New Member Introductions 08-08-2015, 03:47 PM
Replies: 35
Views: 4,978
Posted By mmwjr
Being that the floor is solid is a good thing. ...

Being that the floor is solid is a good thing.

Where it says URL is another tab which allows you to browse you computer directory to attach photos.
Forum: Welcome Mat | New Member Introductions 08-07-2015, 11:16 PM
Replies: 35
Views: 4,978
Posted By mmwjr
Boat model, year and some pictures would be...

Boat model, year and some pictures would be helpful.
Forum: Welcome Mat | New Member Introductions 08-05-2015, 11:16 AM
Replies: 35
Views: 4,978
Posted By mmwjr
Going up 1" of pitch should drop the WOT by about...

Going up 1" of pitch should drop the WOT by about 250 rpm.

I would try mercruiser's prop calculator and see what it recommends.
Forum: Welcome Mat | New Member Introductions 07-19-2015, 10:56 AM
Replies: 35
Views: 4,978
Posted By mmwjr
The mixture screws are on the front of the carb...

The mixture screws are on the front of the carb down near the base plate.

If altitude is to high at the lake the carb may need to be jetted differently. I would ask other boaters at the lake if...
Forum: Welcome Mat | New Member Introductions 07-03-2015, 11:03 PM
Replies: 35
Views: 4,978
Posted By mmwjr
The trim sender is on the side of the gimbal ring...

The trim sender is on the side of the gimbal ring on the outside of the transom assembly. Either the wires are broken off of it or it's bad internally. The easiest time to replace these is when...
Forum: Welcome Mat | New Member Introductions 06-17-2015, 08:44 PM
Replies: 35
Views: 4,978
Posted By mmwjr
IMO I would replace all 3 bellows, gimbal...

IMO I would replace all 3 bellows, gimbal bearing, water hose, lube hose, trim limit and trim sender, lower shift cable, and the u-joints (cheap and you are there).

Also have them check the...
Forum: Welcome Mat | New Member Introductions 06-17-2015, 11:15 AM
Replies: 35
Views: 4,978
Posted By mmwjr
No problems in removing the drive it has a valve...

No problems in removing the drive it has a valve interface that will close when you pull the drive to prevent the lube from running out.
Forum: Welcome Mat | New Member Introductions 06-15-2015, 02:41 AM
Replies: 35
Views: 4,978
Posted By mmwjr
The B3 dual props provide torque canceling that...

The B3 dual props provide torque canceling that limits slow speed wander in single engine boats and provides more bite. If you want the benefits of it buy a boat with it already installed unless you...
Forum: Welcome Mat | New Member Introductions 06-14-2015, 12:14 PM
Replies: 35
Views: 4,978
Posted By mmwjr
To switch to any Bravo you would need to remove...

To switch to any Bravo you would need to remove the engine, replace transom assembly with a bravo one, install an inboard raw water pump, add Bravo drive.
Forum: Welcome Mat | New Member Introductions 06-12-2015, 10:30 PM
Replies: 35
Views: 4,978
Posted By mmwjr
+1 what Kev said

+1 what Kev said
Forum: Welcome Mat | New Member Introductions 06-12-2015, 10:21 AM
Replies: 35
Views: 4,978
Posted By mmwjr
Welcome aboard Where did it sound like the...

Welcome aboard

Where did it sound like the noise was coming from, engine or drive?

Did you check the fluid level, oil, gear lube, ...

Any other symptoms, engine get hot, gauges readings,...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT. The time now is 12:43 PM.

Contact Us - Maxum Owners Club - Archive - Community Rules - Terms of Service - Privacy - Accessibility - Top

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.