Showing results 1 to 25 of 62
Search took 0.00 seconds.
Search: Posts Made By: BayBoy
Forum: Maxum Maintenance 06-25-2013, 01:55 PM
Replies: 11
Views: 3,904
Posted By BayBoy
Should be able to get the exact part number here....

Should be able to get the exact part number here. A little cross reference work on Google should get you to a cheaper automotive equivalent. https://www.maxumcustomercare.com
Forum: Electronics 06-25-2013, 01:36 PM
Replies: 4
Views: 3,027
Posted By BayBoy
I did this already on a 3200 SCR. On the...

I did this already on a 3200 SCR. On the starboard side rub rail about every third screw is extra long and screws into the back of the corner trim piece inside the salon area. When you remove all...
Forum: Engines 06-25-2013, 01:21 PM
Replies: 2
Views: 1,945
Posted By BayBoy
This is an old model. If you need to replace in...

This is an old model. If you need to replace in kind you may try eBay as there are several listed as reasonable prices. What is wrong with the old one? May be easier to find the parts you need and...
Forum: Engines 06-25-2013, 12:57 PM
Replies: 3
Views: 1,537
Posted By BayBoy
You would think it would be a standard size...

You would think it would be a standard size however I ordered a pair of remote oil drain hoses for mine (twin 5.7 2 bl) that stated they were for that engine and the thread pitch was wrong.
Forum: Maxum Owners General Discussions 06-19-2013, 03:00 AM
Replies: 9
Views: 1,865
Posted By BayBoy
Not sure why the outdrive would vibrate at idle...

Not sure why the outdrive would vibrate at idle since the only thing turning is the pinion gear at the top end. Clutch pack may have taken a hit when it locked up.
Forum: Engines 06-19-2013, 02:34 AM
Replies: 3
Views: 1,434
Posted By BayBoy
Serial number is stamped on a nameplate and...

Serial number is stamped on a nameplate and riveted to the right side of the block at the bellhousing. You can do a S/N lookup on the Mercruiser site to very year. Sounds like it might be a...
Forum: Engines 06-19-2013, 02:20 AM
Replies: 3
Views: 1,567
Posted By BayBoy
This is the casting boss for a manual fuel pump. ...

This is the casting boss for a manual fuel pump. There is a detent at the deepest portion of the boss that is drilled out for the cam actuator if the engine is being fitted with a manual pump. 4.3...
Forum: Maxum Maintenance 07-08-2011, 03:20 AM
Replies: 4
Views: 1,738
Posted By BayBoy
Most regulators can handle 100psi with no...

Most regulators can handle 100psi with no problem. Not sure I understand what is blowing/leaking or where.
Forum: Maxum Maintenance 07-08-2011, 03:03 AM
Replies: 2
Views: 2,165
Posted By BayBoy
Not sure if you are asking a question or making a...

Not sure if you are asking a question or making a statement. Bilge pumps also draw battery power as well as the Mercathode system (if equipped) even with the battery switches turned off as they are...
Forum: Maxum Maintenance 07-08-2011, 02:59 AM
Replies: 24
Views: 9,115
Posted By BayBoy
You also have the emergency kill switches (little...

You also have the emergency kill switches (little red buttons with lanyards attached to them) in the loop. Since they are rarely used they can corode over time.
Forum: Sport Yachts 07-08-2011, 02:51 AM
Replies: 7
Views: 3,494
Posted By BayBoy
The problem is most likely in the circuit board...

The problem is most likely in the circuit board in the back of the fridge that toggles you back and forth from AC to DC. Need to pull out the fridge, kill the power and swap out the board. About a...
Forum: Sport Yachts 07-08-2011, 02:38 AM
Replies: 11
Views: 4,243
Posted By BayBoy
Which way are you putting them in? The go in...

Which way are you putting them in? The go in from the outside of the boat not the inside. Another trick is to take a small needle and bore a small hole through one of the screen frame tabs (go...
Forum: Sport Yachts 07-08-2011, 02:29 AM
Replies: 4
Views: 3,954
Posted By BayBoy
It's not that bad actually. Only one out of...

It's not that bad actually. Only one out of every four screws in the rub rail go all the way through to the trim panel. It's a 2 person job as you need to have someone hold the interior panel while...
Forum: Sport Yachts 07-08-2011, 02:21 AM
Replies: 6
Views: 2,746
Posted By BayBoy
I took a piece of solid foam insulation (the type...

I took a piece of solid foam insulation (the type used to insulate basement walls) and cut it to fit just inside the cooler opening. I fastened it to the lid so that it makes an interlocking seal...
Forum: Sport Yachts 07-08-2011, 01:52 AM
Replies: 5
Views: 3,703
Posted By BayBoy
Yes, the sell it along with the plexiglass. ...

Yes, the sell it along with the plexiglass. Sells by the foot and they know how much you need. As I recall they also sell the adhesive but at a pretty steep mark-up. Just get the specific brand...
Forum: Sport Yachts 07-08-2011, 01:45 AM
Replies: 0
Views: 1,485
Posted By BayBoy
Angry No top end

Hey fellow boaters. Got another issue. I have a 1999 Maxum 3200 SCR w/ 5.7 2lb Bravo II's. Engines are running great and, while in neutral, will rev right up to 4800 rpm with no problem. Note: I...
Forum: Sport Yachts 07-08-2011, 01:07 AM
Replies: 5
Views: 3,703
Posted By BayBoy
I have replaced mine twice. Measure the hatch...

I have replaced mine twice. Measure the hatch glass. Parts book says it should be 20.25" x 20.25" Bomar. Then call:

Bomar Customer Service Location
PO Box 1200
South West Street...
Forum: Engines 05-24-2011, 06:23 PM
Replies: 2
Views: 1,437
Posted By BayBoy
Thanks. I'll give it a try. Replaced the...

Thanks. I'll give it a try. Replaced the starter several years back and did it almost entirely by feel due to location. My genset sits about 8" away which makes it very tight. One of my...
Forum: Engines 05-24-2011, 05:25 PM
Replies: 2
Views: 1,437
Posted By BayBoy
Unhappy Nothing but a click from the starter

Can't figure this one out. Boat ran fine in the fall. Put back in several weeks ago after winter storage. Port engine started after a few cranks. Starboard engine cranked and cranked but would...
Forum: Maxum Owners General Discussions 07-14-2009, 01:36 PM
Replies: 1
Views: 1,335
Posted By BayBoy
Re: First boat!

You will learn quickly that you either love it or hate it. Stay on top of your maintenance, obey the rules of the road, understand that BOAT is just an acronym for Break Out Another Thousand, and...
Forum: Electronics 07-13-2009, 04:50 PM
Replies: 3
Views: 1,882
Posted By BayBoy
Re: 35 amp inlet breaker

Call Carling direct @ Carling Technologies Customer Care Center: 860/793-9281. They most likely have a new part number cross reference for that breaker. Get the new part number and the do a Google...
Forum: Maxum Owners General Discussions 07-13-2009, 12:03 AM
Replies: 4
Views: 3,197
Posted By BayBoy
Re: bomar hatch on 2700scr

You can contact Pompanette direct and get just the lense. Be sure to have the dimensions of the hatch and the Maxum part number so you get the correct one. You can also usually choose between white...
Forum: Maxum Owners General Discussions 07-11-2009, 02:00 AM
Replies: 6
Views: 1,968
Posted By BayBoy
Re: 1997 3000SCR Water in Mid Bilge from AC unit?

That's where they drain. Be sure to keep the fwd bilge pump in good working order.
Forum: Engines 07-09-2009, 04:44 PM
Replies: 3
Views: 2,104
Posted By BayBoy
Re: power steering question

Typically both engines have the same identical pump/pulley/belt set up with only one of the pumps actully piped to the power steering unit (normally starboard in a twin setup) and the other is piped...
Forum: Maxum Owners General Discussions 07-09-2009, 04:29 PM
Replies: 11
Views: 3,392
Posted By BayBoy
Re: boating in the dark Q's?

#1) Be sure to use your nav lights but don't expect others to use them. The later sounds rather stupid but I boat on the Chesapeake Bay and am amazed by how many boats either don't use nav lights or...
Showing results 1 to 25 of 62

 
Forum Jump

All times are GMT. The time now is 10:40 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.