Reply
 
Thread Tools Search this Thread Display Modes
 
Old 09-20-2012, 12:07 PM   #1
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default New LED lights and rewired the Trailer

While I am waiting on the Seals.... I installed New LED lights and rewired the Trailer last night. I went to Wal-Mart and got the Blazer LED Low Profile Submersible Trailer Light Kit. Good Kit except the Wire harness was about 3' short, so I went to the auto parts store and bought 25' of trailer wires. Spliced it on the New harness up by the Plug. I wanted as few Splices exposed to the Water as possible. I also put shrink wrap over the splices to keep the water out of the connections. The rest of the installation went without a hitch (lol). LED's are BRIGHT. Total cost was $65.00 and about 2 hours of work. Oh I put new Side markers on as well.

So far I've got about $600 bucks invested in this trailer. Maybe I am abet overly cautious with this trailer but with the Boat/Trailer weight so close the Towing capacity of my truck I want everything working top notch. I think once I get all done I'm going to the local scale and see how much it weighs. I figure about 5800Lbs. I'll let everyone know when I get it done.


Todd
__________________

9Ball is offline   Reply With Quote
Old 09-20-2012, 02:35 PM   #2
Admiral

 
ss3964spd's Avatar
 
Join Date: Jul 2009
Location: Fairfax Va
Posts: 1,512
Send a message via Yahoo to ss3964spd
Default

I'll be very interested in seeing how much it weighs. I believe it's going to be over 6K - perhaps quite a bit more.

Do you have brakes on both axles, Todd? I need to do a brake job on my trailer too.

Dan
__________________

ss3964spd is offline   Reply With Quote
Old 09-20-2012, 06:12 PM   #3
Commander
 
Join Date: Aug 2010
Location: Purcellville, VA.
Posts: 296
Default

I'll second that question. I need to do mine as well. That would be brakes on both axles, all brake lines and surge coupler.

Also, do yourself a favor and throw out those old butt splices and shrink wrap and get yourself some of these:
http://www.amazon.com/gp/product/B000BVZB8E/

You can get them in red (22-18ga), blue (16-14ga) and yellow (12-10ga). I have been using these for the last 6-8 years and I love them. Just crimp them on as normal and then put a torch on it to shrink it. When done correctly a bit of goop starts to ooze out at the wire forming a bead, that is when you know it is good.

I have never had one of these corrode and I have used them on trailers, boats and cars.

LOVE THEM!!
mcoffey is offline   Reply With Quote
Old 09-20-2012, 08:42 PM   #4
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

I only have brakes on the front axle.

Here's the number for Dave's boat trailer sales 432 crain hwy NE. Glen Burnie MD. 410-761-6460.

Sent from my VS920 4G using Tapatalk 2
9Ball is offline   Reply With Quote
Old 09-20-2012, 08:44 PM   #5
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

Not sure I'll get to weigh it this weekend but when I do I'll post it so everyone will have an idea... seems to come up on the forms quite a bit.

Sent from my VS920 4G using Tapatalk 2
9Ball is offline   Reply With Quote
Old 09-21-2012, 04:00 PM   #6
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

Awesome, but think I'll wait till spring. I'm in the eng rebuild phase now.

Todd


Quote:
Originally Posted by mcoffey View Post
I'll second that question. I need to do mine as well. That would be brakes on both axles, all brake lines and surge coupler.

Also, do yourself a favor and throw out those old butt splices and shrink wrap and get yourself some of these:
http://www.amazon.com/gp/product/B000BVZB8E/

You can get them in red (22-18ga), blue (16-14ga) and yellow (12-10ga). I have been using these for the last 6-8 years and I love them. Just crimp them on as normal and then put a torch on it to shrink it. When done correctly a bit of goop starts to ooze out at the wire forming a bead, that is when you know it is good.

I have never had one of these corrode and I have used them on trailers, boats and cars.

LOVE THEM!!
9Ball is offline   Reply With Quote
Old 09-28-2012, 12:01 PM   #7
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

Put the grease seals in the hubs last night.. the trailer is now completely done new brakes new lights new wires. next is to get it weighed this morning.

Sent from my VS920 4G using Tapatalk 2
9Ball is offline   Reply With Quote
Old 09-28-2012, 12:42 PM   #8
Admiral

 
ss3964spd's Avatar
 
Join Date: Jul 2009
Location: Fairfax Va
Posts: 1,512
Send a message via Yahoo to ss3964spd
Default

Just the trailer, or the boat and the trailer?

If both, don't forget to throw all the engine bits you've removed back into the bilge! For accuracy, of course.

Dan
ss3964spd is offline   Reply With Quote
Old 09-28-2012, 01:59 PM   #9
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

Boat and trailer weigh 6380lbs. A lot more than I thought...

Sent from my VS920 4G using Tapatalk 2
9Ball is offline   Reply With Quote
Old 09-28-2012, 03:44 PM   #10
Admiral

 
ss3964spd's Avatar
 
Join Date: Jul 2009
Location: Fairfax Va
Posts: 1,512
Send a message via Yahoo to ss3964spd
Default

Hmmm, not quite as much as I thought it would Todd. Does that include the cylinder heads, intake and exhaust manifolds, and risers that you removed? Is there any gas in the tank?

Dan
ss3964spd is offline   Reply With Quote
Old 09-28-2012, 06:49 PM   #11
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

I don't know how much gas is in it.. I'll tell you. I don't think I'll trailer it any distance.. local only

Sent from my VS920 4G using Tapatalk 2
9Ball is offline   Reply With Quote
Old 09-28-2012, 07:59 PM   #12
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

There is gas on the boat I just don't know how much.. heads inttake an exhaust manifolds are off

Sent from my VS920 4G using Tapatalk 2
9Ball is offline   Reply With Quote
Old 10-01-2012, 01:38 PM   #13
Admiral

 
ss3964spd's Avatar
 
Join Date: Jul 2009
Location: Fairfax Va
Posts: 1,512
Send a message via Yahoo to ss3964spd
Default

So add in approximately, and maybe conservatively, 200 pounds worth of engine parts. Then say, for example, 30 gallons of fuel @ 183 pounds-ish. That rig is nudging up against, what, 6800 pounds? Probably about right with the trailer.
ss3964spd is offline   Reply With Quote
Old 10-01-2012, 03:43 PM   #14
Commander
 
9Ball's Avatar
 
Join Date: Jul 2011
Location: Port St Lucie, FL
Posts: 469
Default

Yes I think thats a good guess. Just over the Tow limits of my truck. I think I'll try and get a slip here on base when I drop it in the water. cost is $1080.00 from Apr - Nov. not too bad I guess. thats water and Elec included.
__________________

9Ball is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Powered by vBadvanced CMPS v3.2.3

All times are GMT. The time now is 06:23 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.