Reply
 
Thread Tools Search this Thread Display Modes
 
Old 12-23-2013, 12:50 PM   #21
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

I did pull both head, I thought that when one side was blown then it's better to take both, it would felt quite bad when I fire her up again and the first trip next side breaks down.

As I mentioned the value them self might not be correct it,s more the difference between the values that's interesting, my compression tester cost mi like 20$ so I don't think it's very accurate.
__________________

Fippe is offline   Reply With Quote
Old 12-23-2013, 01:29 PM   #22
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Perry Hall, Maryland
Posts: 5,403
Default

I agree with doing both heads. This allows you to have fresh heads and new gaskets since you are already torn down this far.
When do you plan to reassemble? Post pictures as you do so.
__________________

__________________
Mike
mmwjr is offline   Reply With Quote
Old 12-23-2013, 01:38 PM   #23
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

I'm going to buy some paint for the heads and intake as soon as the stores open after x-mas,
When I have re-painted the parts again I will reassemble the engine,
Probably in January.
I will post updates and pic along the reassemble.
Fippe is offline   Reply With Quote
Old 12-29-2013, 04:25 PM   #24
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

IMG_2008.jpgIntakt before repainting, some rust that didn't look so good,
Fippe is offline   Reply With Quote
Old 12-29-2013, 04:45 PM   #25
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

intake after sandblasting and repainting with Quicksilver enamel spray paint.IMG_2065.jpgIMG_2066.jpgIMG_2067.jpg
i also repainted the heatexchanger.
Fippe is offline   Reply With Quote
Old 12-29-2013, 06:14 PM   #26
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Perry Hall, Maryland
Posts: 5,403
Default

Fippe looks nice painted however you got paint on the bolt threads and it looks in the threads of th intake for the distributor hold down.
I recommend cleaning these up with a tap (intake threads) and die (bolt threads).
When do you get the heads back?
__________________
Mike
mmwjr is offline   Reply With Quote
Old 12-29-2013, 06:46 PM   #27
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

Quote:
Originally Posted by mmwjr View Post
Fippe looks nice painted however you got paint on the bolt threads and it looks in the threads of th intake for the distributor hold down.
I recommend cleaning these up with a tap (intake threads) and die (bolt threads).
When do you get the heads back?
It's correct that I got some paint in the threads, I'm going clean them up,
I've got the head back and now when the intake is painted and that went well I try too touch up the heads a bit.
Fippe is offline   Reply With Quote
Old 04-01-2014, 07:27 AM   #28
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

Some update, I was supposed too put the engine together in January but it got a bit cold outside so I started last Sunday instead,
I bought new bolts too make the reassembling easier,
Started too clean the surface, so far everything vent well.
Soon the first head was on place, started whit the next and everything felt really good until it was time too put the pushrods and rocker arms on place when I first notice that the moron who renovated the heads had put back a exhaust valve that is to short, they had cut of to much of the valve shaft.
Now I have to lift the head again go back too the workshop and the change the valve.
I got a bit mad at my self for not notice that before I put the head back.
Fippe is offline   Reply With Quote
Old 04-01-2014, 12:01 PM   #29
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Perry Hall, Maryland
Posts: 5,403
Default

I hear you. Only 1 valve wrong should have stood out but this long winter has gotten to us all.

BTY if you had already torqued the head bolts the gasket needs to be replaced.
__________________
Mike
mmwjr is offline   Reply With Quote
Old 04-01-2014, 07:36 PM   #30
Lt. JG
 
Join Date: Apr 2013
Posts: 38
Default

Indeed it has, winter is not my favorite time of the year. :-)

I have torques the head :-( I talked too the workshop and they will give me a new head gasket,
And I hope they will not charge me for a new valve and the work to change it when they have messed it up.
__________________

Fippe is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Powered by vBadvanced CMPS v3.2.3

All times are GMT. The time now is 11:21 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2017, vBulletin Solutions, Inc.